Update ARM split keyboard docs (#9160)

* Update ARM split keyboard docs

* Update docs/serial_driver.md

Co-authored-by: Nick Brassel <nick@tzarc.org>

Co-authored-by: Nick Brassel <nick@tzarc.org>
This commit is contained in:
Joel Challis 2020-05-21 21:20:46 +01:00 committed by GitHub
parent 179e5c018f
commit 6d84795bc1
No known key found for this signature in database
GPG key ID: 4AEE18F83AFDEB23
3 changed files with 26 additions and 5 deletions

View file

@ -8,9 +8,20 @@ QMK Firmware has a generic implementation that is usable by any board, as well a
For this, we will mostly be talking about the generic implementation used by the Let's Split and other keyboards.
!> ARM is not yet supported for Split Keyboards. Progress is being made, but we are not quite there, yet.
!> ARM is not yet fully supported for Split Keyboards and has many limitations. Progress is being made, but we have not yet reached 100% feature parity.
## Compatibility Overview
| Transport | AVR | ARM |
|------------------------------|--------------------|--------------------|
| ['serial'](serial_driver.md) | :heavy_check_mark: | :white_check_mark: <sup>1</sup> |
| I2C | :heavy_check_mark: | |
Notes:
1. Both hardware and software limitations are detailed within the [driver documentation](serial_driver.md).
## Hardware Configuration
This assumes that you're using two Pro Micro-compatible controllers, and are using TRRS jacks to connect to two halves.

View file

@ -36,7 +36,7 @@ These are defaults based on what has been implemented for ARM boards.
| [RGB Lighting](feature_rgblight.md) | Disabled |
| [Backlight](feature_backlight.md) | Forces [task driven PWM](feature_backlight.md#software-pwm-driver) until ARM can provide automatic configuration |
| USB Host (e.g. USB-USB converter) | Not supported (USB host code is AVR specific and is not currently supported on ARM) |
| [Split keyboards](feature_split_keyboard.md) | Not supported yet |
| [Split keyboards](feature_split_keyboard.md) | Partial - heavily dependent on enabled features |
## Manual Conversion

View file

@ -1,7 +1,7 @@
# 'serial' Driver
This driver powers the [Split Keyboard](feature_split_keyboard.md) feature.
!> Serial in this context should be read as **sending information one bit at a time**, rather than implementing UART/USART/RS485/RS232 standards.
?> Serial in this context should be read as **sending information one bit at a time**, rather than implementing UART/USART/RS485/RS232 standards.
All drivers in this category have the following characteristics:
* Provides data and signaling over a single conductor
@ -11,7 +11,7 @@ All drivers in this category have the following characteristics:
| | AVR | ARM |
|-------------------|--------------------|--------------------|
| bit bang | :heavy_check_mark: | Soon™ |
| bit bang | :heavy_check_mark: | :heavy_check_mark: |
| USART Half-duplex | | :heavy_check_mark: |
## Driver configuration
@ -35,6 +35,12 @@ Configure the driver via your config.h:
// 5: about 20kbps
```
#### ARM
!> The bitbang driver causes connection issues with bitbang WS2812 driver
Along with the generic options above, you must also turn on the `PAL_USE_CALLBACKS` feature in your halconf.h.
### USART Half-duplex
Targeting STM32 boards where communication is offloaded to a USART hardware device. The advantage is that this provides fast and accurate timings. `SOFT_SERIAL_PIN` for this driver is the configured USART TX pin. **The TX pin must have appropriate pull-up resistors**. To configure it, add this to your rules.mk:
@ -56,4 +62,8 @@ Configure the hardware via your config.h:
#define SERIAL_USART_TX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
```
You must also turn on the SERIAL feature in your halconf.h and mcuconf.h
You must also enable the ChibiOS `SERIAL` feature:
* In your board's halconf.h: `#define HAL_USE_SERIAL TRUE`
* In your board's mcuconf.h: `#define STM32_SERIAL_USE_USARTn TRUE` (where 'n' matches the peripheral number of your selected USART on the MCU)
Do note that the configuration required is for the `SERIAL` peripheral, not the `UART` peripheral.